The following configuration settings are automatically supplied to all TekSavvy supplied Grandstream HT502 ATAs.
If you've purchased a Grandstream HT502 ATA through an alternate vendor, feel free to use the following configuration to match your ATA to our tried and tested configuration:
Grandstream HT502 Line 1 Configuration
Canadian FREE VOIP - freephoneline.ca
LOGON REQUIRED at freephoneline.ca
ATA settings can be obtained from the user profile by navigating to the following :
https://www.freephoneline.ca/showSipSettings
- YOUR SIP STATUS - freephoneline.ca
- YOUR SIP SETTINGS - freephoneline.ca
FXS PORT1 Settings: | |
---|---|
Account Active: | YES |
Primary SIP Server: | voip.freehoneline.ca |
Failover SIP Server: | |
Prefer Primary SIP Server: | YES |
Outbound Proxy: | voip.freehoneline.ca |
SIP Transport: | UDP |
NAT Traversal: | NO |
SIP User ID: | Your phone number. Just the numbers, no dashes. |
Authenticate ID: | |
Authentication Password: | Your password |
Name: | Your phone number. Just the numbers, no dashes. |
DNS Mode: | A Record |
DNS SRV use Registered IP | |
Primary IP: | |
Backup IP1: | |
Backup IP2: | |
Tel URI: | Disabled |
SIP Registration: | YES |
Unregister On Reboot: | NO |
Outgoing Call without Registration: | NO |
Register Expiration: | 30 |
Register before Expiration: | 0 |
SIP Registration Failure Rety Wait Time: | 20 |
SIP Registration Failure Retry Wait Time upon 403 Forbidden: | 1200 |
Layer 3 QoS | 26 |
46 | |
Local SIP Port: | 5060 |
Local RTP Port: | 5004 |
Use Random Port: | NO |
Hold Target Before Refer | YES |
Refer-To Use Target Contact: | NO |
Transfer on Conference Hangup: | NO |
Disable Bellcore Style 3-Way Conference: | NO |
Remove OBP from Route Header: | NO |
Support SIP Instance ID: | YES |
Validate Incoming SIP Message: | YES |
Check SIP User ID for incoming INVIE: | YES |
Authenticate incoming INVITE: | NO |
Authenticate server certificate domain: | NO |
Authenticate server certificate chain: | NO |
Trusted CA certificates | |
Allow Incoming SIP Messages from SIP Proxy Only: | YES |
Use Privacy Header: | Default |
Use P-Preferred-Identity Header | Default |
SIP T1 Timeout: | 0.5 sec |
SIP T2 Timeout: | 4 sec |
SIP Timer D: | 0 |
DTMF Payload Type: | 101 |
Preferred DTMF method (in listed order): | Priority 1: RFC2833 Priority 2: In-audio Priority 3: SIP INFO |
DTMF-RELAY Tag Respect SIP INFO | NO |
Disable DTMF Negotiation: | NO |
Send Hook Flash Event: | NO |
Enable Call Features: | NO |
Offhook Auto-Dial: | |
Offhook Auto-Dial Delay: | 0 |
Proxy-Require: | |
Use NAT IP: | |
Use SIP User-Agent Header: | |
Distinctive Ring Tone: | Ring Tone 1 used if incoming caller ID is Ring Tone 1 used if incoming caller ID is Ring Tone 1 used if incoming caller ID is |
Disable Call-Waiting: | NO |
Disable Call-Waiting Caller ID: | NO |
Disable Call-Waiting Tone: | NO |
Disable Connected Line ID | NO |
Disable Receiver Offhook Tone: | NO |
Disable Reminder Ring for On-Hold Call: | NO |
Disable Visual MWI: | NO |
Do Not Escape '#' as %23 in SIP URIL | NO |
Disable Multiple m line in SDP: | NO |
Ring Timeout: | 60 |
Delayed Call Forward Wait Time: | 20 |
No Key Entry Timeout: | 4 |
Early Dial: | NO |
Dial Plan Prefix: | |
Use # as Dial Key: | YES |
Dial Plan: | {*98|*80|*73|*78|*79|*60|*69|*31x|*xx[2-9]xx[2-9]xxxxxx|*xx1[2-9]xx[2-9]xxxxxx|310xxxx|[2-9]x+|1[2-9]xx[2-9]xxxxxx|[2-9]xxxxxxxxx|011xxxxxxx.|101xxxxxxxxxxxxx.|*75[2-4]x[2-9]xxxxxxxxx|*75[2-4]x1[2-9]xxxxxxxxx} |
SUBSCRIBE for MWI: | NO, do not send SUBSCRIBE for Message Waiting Indication |
Send Anonymous: | NO |
Anonymous Call Rejection: | NO |
Special Feature: | Standard |
Session Expiration: | 180 |
Min-SE: | 90 |
Caller Request Timer: | NO |
Callee Request Timer: | NO |
Force Timer: | NO |
UAC Specify Refresher: | Omit (Recommended) |
UAS Specify Refresher: | UAC |
Force INVITE: | NO |
Send Re-INVITE After Fax: | NO |
Enable Silence Detection for Fax Disconnect: | YES |
Enable 100rel: | NO |
Add Auth Header On Initial REGISTER: | NO |
Use First Matching Vocoder in 200OK SDP: | NO |
Preferred Vocoder: (in listed order) | choice 1: G729 choice 2: PCMU choice 3: G723 choice 4: G729 choice 5: G726-32 choice 6: iLBC choice 7: AAL2-G726-40 choice 8: G729E |
Voice Frames per TX: | 2 |
G723 Rate: | 6.3kbps encoding rate |
iLBC Frame Size: | 20ms |
iLBC Payload Type: | 97 |
AAL2-G726-16 Payload Type: | 100 |
AAL2-G726-24 Payload Type: | 99 |
AAL2-G726-32 Payload Type: | 104 |
AAL2-G726-40 Payload Type: | 103 |
G729E Payload Type: | 102 |
VAD: | NO |
Symmetric RTP: | NO |
Fax Mode: | T.38 (Auto Detect) |
Fax Tone Detection Mode: | Callee |
Jitter Buffer Type: | Adaptive |
Jitter Buffer Length: | Medium |
SRTP Mode: | Disabled |
Crypto Life Time: | Enabled |
SLIC Setting: | USA |
Caller ID Scheme: | Bellcore/Telcordia |
Polarity Reversal: | NO |
Loop Current Disconnect: | NO |
Play busy/reorder tone before Loop Current Disconnect: | NO |
Loop Current Disconnect Duration: | 200 |
Enable Hook Flash: | Yes |
Hook Flash Timing: | minimum: 300 maximum: 1100 |
On Hook Timing: | 400 |
Gain: | TX: 0dB default RX: 0dB default |
Disable Line Echo Canceller (LEC): | NO |
Ring Tones (Syntax: c=on1/off1-on2/off2-on3/off3;) | Ring Tone 1: c=2000/4000; Ring Tone 2: c=2000/4000; Ring Tone 3: c=2000/4000; Ring Tone 4: c=2000/4000; Ring Tone 5: c=2000/4000; Ring Tone 6: c=2000/4000; Ring Tone 7: c=2000/4000; Ring Tone 8: c=2000/4000; Ring Tone 9: c=2000/4000; Ring Tone 10: c=2000/4000; |
Blacklist For Incoming Calls | Blocked Number 1: Blocked Number 2: Blocked Number 3: Blocked Number 4: Blocked Number 5: Blocked Number 6: Blocked Number 7: Blocked Number 8: |
Grandstream HT502 Freephoneline.ca Setup
ADVANCED SETTINGS - BEFORE - Unchanged - Factory Setting
ADVANCED SETTINGS - AFTER
FXS PORT 1
No comments:
Post a Comment
NOTE:: sent to the “shit list” bullshit spam messages with links. DO NOT WASTE YOUR TIME !!!!